Lumatrax II Anti-Slip Floor Coating
and now, Lumatrax SMC Safety Marking Coating

WHEN SECONDS COUNT,
LUMATRAX SHOWS THE WAY OUT

Both of these coatings are designed to meet the stringent new ASTM E 2072* Standards for Photoluminescent Safety Markings. This means you get one of the brightest, non-radioactive coatings available today.

LUMATRAX II LUMINESCENT ANTI-SLIP FLOOR COATING
LUMATRAX SMC SAFETY MARKING COATING

In an emergency situation, it's too late to make sure your employees can see the way out. American Safety Technologies, long the leader in traction enhancing anti-slip coatings, announces the introduction of two industry leading glow-in-the-dark coatings: Lumatrax II Anti-Slip Floor Coating and now, Lumatrax SMC Safety Marking Coating.

Both of these coatings are designed to meet the stringent new ASTM E 2072* Standards for Photo luminescent Safety Markings. This means you get one of the brightest, non-radioactive coatings available today. *For more information on ASTM E 2072, please visit them at www.astm.org

SOLUTIONS YOU CAN SEE...
...SAFETY YOU CAN COUNT ON.

Why wait until darkness or other low light conditions threaten the ability of your workers to exit the facility safely in an emergency condition? Lumatrax II or Lumatrax SMC coatings can provide your company with one of the best exit marking systems in the industry. Designed to meet the tough new ASTM standards, these products can glow up to 4 hours to the dark adapted eye, and recharge in minutes with exposure to artificial light sources. We urge you to test Lumatrax systems against the competition.

Lumatrax II
Luminescent Anti-Slip Floor Coating

LUMATRAX II is an interior phosphorescent, waterborne, acrylic polymer anti-slip floor and deck coating. It is designed as a safety coating for pedestrian grade traffic in areas of low illumination or emergency egress. Formulated to meet or exceed the glow properties defined in ASTM-E2072 “Standard Specification for Photo luminescent Safety Markings”, it will glow for up to 4 hours to the dark-adapted eye.

LUMATRAX II safety coating is easy to apply, dries quickly and offers optimum adhesion to asphalt, concrete, wood, and metal surfaces.  It is a water-based coating so clean up is fast and inexpensive.

LUMATRAX II can be used straight out of the can as needed and then resealed for later use.

LUMATRAX II LUMINESCENT ANTI-SLIP FLOOR COATING
Lumatrax II will not only create an illuminated exit path, but will also provide a safe anti-slip surface even under wet or oily conditions. Based on a water-based, single component, elastomeric acrylic polymer, Lumatrax II provides a tough, sealed surface that is specially formulated for pedestrian traffic.

Specifications:
LUMATRAX II LUMINESCENT ANTI-SLIP FLOOR COATING
VOC
 0.34 lbs./gal.(42 g./ltr.)
Volume Solids
 68%
Dry Time - Light traffic
Heavy traffic
 4 hours @ 70°F (21°C)
24 hours @ 70°F (21°C)
Estimated Coverage
70 sq.ft./gal
 bristle roller
Weight per Gallon
 15.2 lbs./gal.(1.8 kg./ltr.)
Flash Point
 >200°F (93.3°C) - CC
Coefficient of Friction ASTM F609
Dry
Wet
 1.30
0.90
Packaging
 1 gal.
Photoluminence
 2.8 mcd/sq.m.@ 60 min.
Lumatrax SMC
Acrylic Safety Marking Coating

LUMATRAX SMC is a single component, water-based acrylic coating. This phosphorescent photoluminescent coating is designed for the marking of aisle ways, doorways, handrails, basements, tunnels, around machinery, stairwells, emergency exits, or any passageway which needs to be identified in the event of an emergency when no other light source is available. When exposed to artificial light, LUMATRAX SMC glows to illuminate the safe passageway of an exit. Formulated to meet or exceed the glow properties defined in ASTM E2072 “Standard Specification for Photoluminescent Safety Markings”, it will glow up to four hours to the dark-adapted eye.

LUMATRAX SMC SAFETY MARKING COATING
Lumatrax is the ideal coating to provide your employees with easily seen exit markings. When electric signs aren't practical and tapes just won't hold up, Lumatrax gives you a versatile option. Easily applied to door frames, handrails, curbs, or obstructions, this water-based acrylic system is compatible with most existing finishes.

Specifications:
LUMATRAX SMC SAFETY MARKING COATING
VOC
 0.18 lbs./gal.(21.42 g./ltr.)
Volume Solids
 62.5%
Dry Time
Recoat
Full Service
 2 hours @ 70°F (21°C)
24 hours @ 70°F (21°C)
Estimated Coverage
200 sq.ft./gal
 brush or spray
at 8 mils WFT/5 mils DFT (may require multiple coats to meet ASTM E 2072)
Weight per Gallon
 11.43 lbs./gal.(1.3 kg./ltr.)
Flash Point
 >200°F (93.3°C) - CC
Packaging
 1 gal./1 qt.sizes
Photoluminence
 2.8 mcd/sq.m.@ 60 min.

Notes:

  • 1. As glow-in-the-dark materials are not exceptionally UV stable by nature, these products are recommended for areas with low UV exposure.
  • 2. The brightest glow of non-radioactive photo luminescent coatings is within the first hour of darkness (depending upon the initial light source and intensity) and will continue to glow for up to four hours to the dark-adapted eye. The glowing characteristics appear different when re-entering into total darkness and depends upon light intensity and the individual.
  • 3. ASTM E 2072-00 (2002) is the Standard Specification for Photoluminescent (Phosphorescent) Safety Markings. ASTM E 2030-02 is a guide for placement of safety marking. For detailed test results for Lumatrax II and Lumatrax SMC systems, please contact our customer service department. For more information on these tests, please visit the American Society for Testing and Materials at www.astm.org.
  • 4. Testing methods may vary from your actual service conditions, and performance of the product may be different as well. Minimum film builds and white primers are required, see technical bulletin for more detail.

CAUTION

Read Material Safety Data Sheet before using this material. Use only with adequate cross ventilation. Keep away from extreme heat, sparks and open flame. Keep from freezing. Avoid prolonged breathing of vapors. For dizziness, seek fresh air. Avoid prolonged contact with skin. Use gloves, goggles and coveralls. In case of spillage on clothing, change clothing to prevent prolonged contact with skin. Wash contaminated clothing before reuse. In case of accidental contact with skin, wash immediately with soap and water. In case of eye contact, flush thoroughly with plenty of water and call physician. If swallowed accidentally, do not induce vomiting. Seek medical attention immediately.

The user of this product is responsible for making its own evaluation and tests regarding the capabilities, safety, utility, suitability and application of the product, and assumes all risks and liabilities resulting from the use or application of the product, whether used alone or with other products. American Safety Technologies (herein referenced to as the COMPANY) warrants only that the product conforms to the specifications contained in product Technical Data Sheets published by the COMPANY, a copy of which is available to the user. If the product fails to conform to this warranty, the user shall return the product within 10 days of the purchase date with a note specifying the defect and the COMPANY will either replace the product or at its option, return the purchase price. EXCEPT AS EXPRESSLY PROVIDED IN THIS PARAGRAPH, THE COMPANY MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND, NATURE OR DESCRIPTION, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, AND HEREBY DISCLAIMS THE SAME.

In no event shall the COMPANY be liable to the user of this product, whether in contract or in tort or any other legal theory (including, without limitation, negligence), for damages which exceed the purchase price of the product, or for any indirect, incidental, consequential or similar damages, arising out of sale, use or application of the product, or for any claim made against the user by any other party, even if American Safety Technologies has been advised of the possibility of such claim.