| FLOOR PATCH KIT
|
IMPAX 5020
Epoxy Floor Resurfacer
A trowel-applied epoxy surfacing and leveling system for new or old floors where extreme physical properties are required. The fast curing, high build finish is durable, anti-slip and reduces downtime.
• Higher physical properties than concrete
• Durable, anti-slip finish
• Convenient kit sizes
|
New Concrete: All surfaces must be firm, free of any laitance or efflorescence, clean, free of any adverse moisture conditions, have an appropriate surface profile, and be well cured before coating. Newly poured concrete must age at least 30 days at temperatures over 70°F before coating. Form release agents, sealers, curing compounds, salts, hardeners and other foreign matter will interfere with adhesion and must be removed. Shot-blasting, mechanical scarification, sandblasting, or suitable chemical means should be employed to prepare substrate.
Old Concrete: Resurfacing older, uncoated concrete floors is done in much the same manner as new concrete. Before preparation, the concrete surface must be thoroughly cleaned with a strong detergent cleaner to remove all grease, oils, etc. All loose concrete must be removed.
Steel/Wood: Application to steel and wood floors is essentially the same as for concrete floors, however the surface preparation and structural considerations vary. Consult our Engineering and Technical Service Department for proper evaluation and recommendations.
Previously Painted Surfaces: Consult ITW Resin Technologies’ Technical Service Department for proper evaluation and recommendations.
(For more detailed information, see Bulletin #400B)
|
 The Right Tools for the Job.
Application of these products is made easy with a speciality sprayer or specialized easy-to-use rollers available from American Safety Technologies. Our napless, phenolic-resin coated, core roller is essential for creating the correct anti-slip profile. The 9" roller cage is built for rugged use. Our heavy-duty fiberglass extension handle allows you to pull the coating towards you with the correct downward pressure. The stainless-steel mixing blade is indispensable for thoroughly blending anti-slip coatings.
See the technical data sheet for complete prep & application techniques.
|
| IMPAX 5020 |
|
COLOR:
|
Cement, Haze Gray, Deck Gray, Tile Red
|
| GLOSS:
|
Not Applicable
|
| VOLUME SOLIDS: |
98% (Primer); 100% (Resurfacer)
|
| VOC: |
Primer<0.2 lbs./gal.- (<25 g/L)
Resurfacer 0 lbs./gal(0 g/L)
|
| COVERAGE:
|
20 sq. ft./batch @ 1/4” thickness
(1.8m2/batch @ 6mm thickness)
|
|
PACKAGING:
|
20 sq. ft. (1.8 m2) unit
480 sq. ft.(44 m2) bulk unit
1440 sq. ft.(133 m2) special bulk unit
|
|
APPLICATION TEMPERATURES:
|
55°F minimum to 95°F maximum
(12°C minimum to 35°C maximum)
*Must be 5°F (3°C) above dew point
|
| RELATIVE HUMIDITY: |
85% maximum
|
| SERVICEABILITY: |
Foot Traffic 12 hrs. @ 72°F (22°C) @ 50% RH
Full Cure: 18 hrs. @ 72°F (22°C) @ 50% RH |
| MIXING RATIO: |
2:1 resin to hardener by volume - primer
2:1 resin to hardener by volume - resurfacer
liquids:40 lbs. of aggregate (1 bag) to 0.9 gal of
Resurfacer liquids |
| INDUCTION: |
None |
| POT LIFE: |
6 hrs. - Primer; 45 min. - Resurfacer |
| FLASH POINT: |
158°F (70°C) PMCC — Primer;
200°F (90°C) PMCC — Resurfacer |
| CLEAN UP: |
IMPAX IXT 59 Solvent |
| ABRASION RESISTANCE: |
5 times concrete |
| COMPRESSIVE STRENGTH: |
10,000 psi (69 M Pa) ASTM-D-695 |
| FLEXURAL STRENGTH: |
2,446 psi (16.7 M Pa) ASTM-D-790 |
| SERVICE TEMPERATURE: |
-10°F to 150°F (-23°C to 65°C) |
| SHELF LIFE: |
18 months in closed container stored
at 50° to 90°F (10° to 32°C) |
|
|
|
Product List
|
WE CAN PROVE IT
A test patch in your facility will prove beyond a doubt that AST Anti-Slip Coatings will stand up to anything your plant can dish out.
CALL TODAY and we will put you in touch with your local American Safety Technologies distributor. They can apply a test patch in your facility that will prove beyond a doubt that AST Coatings will stand up to anything your plant can dish out. Your coating professional can also provide an expert floor or concrete analysis, help you place an order, or answer any questions you may have.
1-800-631-7841
SUPER TECH SUPPORT
Call our technical support hot line for product specifications, MSDS sheets, and answers to all of your technical or application questions.
1-800-631-7841
ITW/American Safety Technologies
130 Commerce Drive
Montgomeryville, PA 18936
|
|
|
Tough Customers
Call for Tough Solutions.
 A TEN-STORY FALL... YOU'RE SHARK BAIT.
One false step on an oil-drilling platform can lead to a 10-story plunge into the ocean. That’s why employees get combat pay to work on a platform. The wet metal gang-planks and ladders are precarious even when not sprayed with salt water, oil and lubricants. But when they’re covered with our anti-slip coatings, suddenly everything’s a lot safer. That’s why the big offshore oil rigs depend on AST to keep them on their feet.
|
|
