| AST ANTI-SLIP COATINGS |
|
Lumatrax II Anti-Slip Floor Coating
and now, Lumatrax SMC Safety Marking Coating
WHEN SECONDS COUNT,
LUMATRAX SHOWS THE WAY OUT
Both of these coatings are designed to meet the stringent new ASTM E 2072* Standards for Photoluminescent Safety Markings. This means you get one of the brightest, non-radioactive coatings available today.
|
LUMATRAX II LUMINESCENT ANTI-SLIP FLOOR COATING
LUMATRAX SMC SAFETY MARKING COATING |
Lumatrax II
Anti-Slip Floor Coating
In an emergency situation, it's too late to make sure your employees can see the way out. American Safety Technologies, long the leader in traction enhancing anti-slip coatings, announces the introduction of two industry leading glow-in-the-dark coatings: Lumatrax II Anti-Slip Floor Coating and now, Lumatrax SMC Safety Marking Coating.
Both of these coatings are designed to meet the stringent new ASTM E 2072* Standards for Photo luminescent Safety Markings. This means you get one of the brightest, non-radioactive coatings available today. *For more information on ASTM E 2072, please visit them at www.astm.org
SOLUTIONS YOU CAN SEE...
...SAFETY YOU CAN COUNT ON.
Why wait until darkness or other low light conditions threaten the ability of your workers to exit the facility safely in an emergency condition? Lumatrax II or Lumatrax SMC coatings can provide your company with one of the best exit marking systems in the industry. Designed to meet the tough new ASTM standards, these products can glow up to 4 hours to the dark adapted eye, and recharge in minutes with exposure to artificial light sources. We urge you to test Lumatrax systems against the competition.
|
Lumatrax II
Luminescent Anti-Slip Floor Coating
LUMATRAX II is an interior phosphorescent, waterborne, acrylic polymer anti-slip floor and deck coating. It is designed as a safety coating for pedestrian grade traffic in areas of low illumination or emergency egress. Formulated to meet or exceed the glow properties defined in ASTM-E2072 “Standard Specification for Photo luminescent Safety Markings”, it will glow for up to 4 hours to the dark-adapted eye.
LUMATRAX II safety coating is easy to apply, dries quickly and offers optimum adhesion to asphalt, concrete, wood, and metal surfaces. It is a water-based coating so clean up is fast and inexpensive.
LUMATRAX II can be used straight out of the can as needed and then resealed for later use.
LUMATRAX II LUMINESCENT ANTI-SLIP FLOOR COATING
Lumatrax II will not only create an illuminated exit path, but will also provide a safe anti-slip surface even under wet or oily conditions. Based on a water-based, single component, elastomeric acrylic polymer, Lumatrax II provides a tough, sealed surface that is specially formulated for pedestrian traffic.
- Extra long glow times
- Water-Based for easy clean up
- Easily applied by brush or roller
- Convenient one gallon units can be resealed and reused
- High coefficient of friction for traction
|
|
|
Specifications:
LUMATRAX II LUMINESCENT ANTI-SLIP FLOOR COATING |
|
VOC
|
0.34 lbs./gal.(42 g./ltr.) |
|
Volume Solids
|
68% |
|
Dry Time - Light traffic
Heavy traffic
|
4 hours @ 70°F (21°C)
24 hours @ 70°F (21°C) |
|
Estimated Coverage
70 sq.ft./gal
|
bristle roller |
|
Weight per Gallon
|
15.2 lbs./gal.(1.8 kg./ltr.) |
|
Flash Point
|
>200°F (93.3°C) - CC |
|
Coefficient of Friction ASTM F609
Dry
Wet
|
1.30
0.90 |
|
Packaging
|
1 gal. |
|
Photoluminence
|
2.8 mcd/sq.m.@ 60 min. |
|
|
Lumatrax SMC
Acrylic Safety Marking Coating
LUMATRAX SMC is a single component, water-based acrylic coating. This phosphorescent photoluminescent coating is designed for the marking of aisle ways, doorways, handrails, basements, tunnels, around machinery, stairwells, emergency exits, or any passageway which needs to be identified in the event of an emergency when no other light source is available. When exposed to artificial light, LUMATRAX SMC glows to illuminate the safe passageway of an exit. Formulated to meet or exceed the glow properties defined in ASTM E2072 “Standard Specification for Photoluminescent Safety Markings”, it will glow up to four hours to the dark-adapted eye.
LUMATRAX SMC SAFETY MARKING COATING
Lumatrax is the ideal coating to provide your employees with easily seen exit markings. When electric signs aren't practical and tapes just won't hold up, Lumatrax gives you a versatile option. Easily applied to door frames, handrails, curbs, or obstructions, this water-based acrylic system is compatible with most existing finishes.
|
|
|
Specifications:
LUMATRAX SMC SAFETY MARKING COATING |
|
VOC
|
0.18 lbs./gal.(21.42 g./ltr.) |
|
Volume Solids
|
62.5% |
|
Dry Time
Recoat
Full Service
|
2 hours @ 70°F (21°C)
24 hours @ 70°F (21°C) |
|
Estimated Coverage
200 sq.ft./gal
|
brush or spray
at 8 mils WFT/5 mils DFT (may require multiple coats to meet ASTM E 2072) |
|
Weight per Gallon
|
11.43 lbs./gal.(1.3 kg./ltr.) |
|
Flash Point
|
>200°F (93.3°C) - CC |
|
Packaging
|
1 gal./1 qt.sizes |
|
Photoluminence
|
2.8 mcd/sq.m.@ 60 min. |
|
|
|
|
Product List
|
|
|
SUPER TECH SUPPORT
Call our technical support hot line for product specifications, MSDS sheets, and answers to all of your technical or application questions.
1-800-631-7841
ITW/American Safety Technologies
130 Commerce Drive
Montgomeryville, PA 18936
|
|
